How To Set Up Sentry Safe Code

Depository Safes

OWNERS Manual

Thank you for purchasing this security safe from Sentry®Safe. This guide is designed to maximize the user and security features of this project.

Getting started

Installation of the batteries (keep door open during setup):

Turn the keypad housing counter clockwise and carefully pull away from the mounting plate to expose battery compartment.
Install four new AAA Alkaline metal batteries (not included). Caution: Concur onto the keypad housing to avoid pulling wires.
Carefully position the keypad into the inserts on the mounting plate and turn clockwise. Ensure that in that location are no wires or cables trapped between the keypad and the mounting plate. Pinched cables result in a short circuit.
Enter: * – Chief or Managing director Code (from front of booklet) – # The lock volition indicate a valid code entry with a single signal and the open light will stay green for five (5) seconds.
Plow the handle clockwise before the light-green light disappears.

Programming your lock codes

The SentrySafe electronic lock is shipped from the factory with a manufactory set master code
& director code (see front of booklet). You lot should set the lock to your ain unique primary & managing director lawmaking immediately. Proceed notes on which lawmaking belongs to which user (Master (User 1), Manager (User 2), User iii, User 4, User 5, User half-dozen and User vii).

A unmarried point (LED fl ashes and beeps in one case) response from the lock indicates valid entry.

A double point (LED fl ashes and beeps twice) response from the lock indicates an
invalid entry.

If iii incorrect entries are entered in a row, the keypad will shut down for a menses of fi ve minutes. During this shut down flow you will not get a response from the keypad.

Irresolute the Main Code

(Lawmaking length: 1 to x digit code) Always perform this functioning with the door open.

Enter: # – Existing Chief Lawmaking – #
The ready light will stay orangish for ten (10) seconds.
Enter: 1 – * – New Master Code – # – New Master Code – #, before the orangish low-cal disappears.

If a error is fabricated during the alter, wait thirty (30) seconds and repeat steps 1 thru 3.
Examination the new lawmaking several times before closing the door: Enter: * – Code – #

The lock will bespeak a valid code alter with a single indicate.
The lock will indicate an invalid code modify with a double bespeak and the old lawmaking is still valid.

Changing the Managing director Lawmaking

(Code length: 1 to 10 digit code) E'er perform this operation with the door open.

Enter: # – Main Code or Manager Lawmaking – #
The set lite will stay orange for ten (10) seconds.
Enter: 2 – * – New Manger Code – # – New Manager Code – #, earlier the orange light disappears.

If a mistake is fabricated during the change, wait 30 (thirty) seconds and echo steps ane thru 3. Exam the new code several times before closing the door: Enter: * – Lawmaking – #

The lock will indicate a valid code change with a single betoken.
The lock will signal an invalid code change with a double signal and the former code is withal valid.

Activate user codes

(Code length: 1 to 10 digit lawmaking) Ever perform this performance with the door open up.

Enter: # – Master Lawmaking or Managing director Code – #
The set low-cal will stay orange for x (ten) seconds.
Enter: User ID Number (3-7) – * – New User Code – # – New User Code – #, earlier the orangish light disappears.

If a mistake is fabricated during the activation, wait thirty (xxx) seconds and repeat steps 1 thru 3.

The lock will point a valid code entry with a single signal.
The lock will indicate an invalid code entry with a double signal and the old code is even so valid.

Example: # – Primary Code or Manger Lawmaking – # – 5 – * – New User Code – # – New User Code – #. This volition actuate User Five (five).

Irresolute the user code

Always perform this operation with the door open

Enter: # – User Code – #
The set light will stay orange for ten (ten) seconds.
Enter: New User Code – # – New User Code – #, before the orangish light disappears.

If a mistake is made during the modify, wait thirty (xxx) seconds and repeat steps 1 thru iii.
Exam the new code several times before closing the door: Enter: * – Code – #

The lock volition indicate a valid code change with a unmarried bespeak.
The lock will point an invalid code change with a double signal and the sometime code is still valid.

The Master and Manager tin besides change the user codes by following the "Activate user
codes" section steps one thru three.

Deleting user codes

Always perform this operation with the door open.

Enter: # – Master Code or Manager Code – #
The set light will stay orange for ten (ten) seconds.
Enter: User ID Number (3-7) – * – # – #

Dual user style

When you desire two people to open up the safe; set your safe to dual user mode. I person enters their code and within 60 (threescore) seconds, the second code is entered. Always perform this operation with the door open.

Whatever Code + Any Lawmaking to unlock

Enter: # – Principal Code – # – 1 – # – 1 – #
The lock will betoken a valid setting change with a unmarried signal.

Master or Manager Code + User Code to unlock

Enter: # – Principal Code – # – 2 – # – ii – #
The lock volition bespeak a valid setting alter with a single indicate.

Opening your safe in dual user manner

Enter: * – 1st Code – # – 2nd Code – #
The lock will indicate a valid code entry with a single bespeak and the open up light will stay dark-green for fi ve (v) seconds.
Turn the handle clockwise before the dark-green light disappears

Returning to single user way (Single code to unlock)

Enter: # – Master Code – # – 0 – # – 0 – #
The lock will point a valid setting change with a unmarried signal.

Time delay mode

Ever perform this operation with the door open. This part will delay both the opening and programming of the lock.

Activate time filibuster

Enter: # – Master Code – # – (01-99) – # – (01-99) – #
The lock will indicate a valid setting change with a unmarried point.
Instance: # – Chief Code – # – 05 – # – 05 – #, this will set a fi ve (5) infinitesimal time delay.
Press * or # to initiate the Fourth dimension Delay.

When time delay is prepare

(During the time delay period the keypad will not respond to any entries)

The lock will fl ash once every fi ve (5) seconds during time delay and will fl ash once every second during the concluding 10 (10) seconds of the fourth dimension delay ending with a double signal.

The lock will fl ash twice every fi ve (5) seconds during the open period. The open catamenia length is two (ii) minutes.

During the open period you can open your rubber (see "How to open your safe, Step 1) or program your safe (following the steps of any programming procedure).

Deactivate time filibuster

Enter: # – Master Lawmaking – # – 00 – # – 00 – #
The lock will betoken a valid setting change with a single signal.

Floor Mount (optional)

This kit contains:

4 (4) Masonry Anchors

Required tools:

Powered Drill
Adjustable Wrench
one/two in. (M12) Masonry Drill

Instructions:

Unlock rubber and open up door.
Remove safe floor carpeting.
Look on the bottom of rubber for four (four) holes with cap plugs.
Remove the cap plugs.
Position the safe in the desired location.
From inside the safety mark the location of the four (4) bolt downward holes.
Move the safe aside to the clear marked spots for drilling.
Using the ½ in. masonry drill, drill a 4 in. deep hole in the marked locations.
Supervene upon the safety in the desired location with the holes in the safe aligned with the
drilled holes in the floor.
Pass each masonry anchor through the safe floor into the drilled holes; making contact with the safe floor.
Tighten each masonry anchor with the adjustable wrench.
Replace safe floor carpet.

Sentry® Group Customer Care

Troubleshooting

Low battery warning

The green LED light will signal in red when opening your safe. The lock is giving you a valid point just is not unlocking.

Irresolute your batteries

Turn the keypad housing counterclockwise and carefully pull away from the mounting plate to expose battery compartment.
Remove the four AAA Alkaline batteries and supervene upon. Caution: Hold onto the keypad housing to avoid pulling wires.
Carefully position the keypad into the inserts on the mounting plate and plough clockwise. Ensure that there are no wires or cables trapped between the keypad and the mounting plate. Pinched cables issue in a brusque circuit.

The lock has no response (no fl ash, no beeps)

Brand sure the wires in the keypad housing are not pinched and are securely connected. (See "installation of batteries" on folio two)
Check to make certain the batteries are correctly and securely inserted into the battery compartment. (See "installation of batteries" on page 2)
Lock tin can possibly exist in the lockout punishment, look fi ve (5) minutes, and check if the lock responds.
Replace the existing batteries with new ones. (See "irresolute your batteries" in troubleshooting)

The lock is responding simply does non unlock

Make certain you are getting a valid response.
Make sure you get a bespeak with every key stroke.
Make sure y'all are not in time filibuster mode. (Run into "fourth dimension delay style" above)
Supervene upon the existing batteries with new ones. (See "irresolute your batteries" in troubleshooting)

If the lock notwithstanding does not open, contact Spotter Grouping Customer Care: one-800-828-1438 or 585-381-4900 (Bachelor Mon – Fri, 8:00 am – half dozen:00 pm EST). Follow the instructions carefully to become the best possible apply from your lock.

Address

Ezoic

SentrySafe Lock Lawmaking Programming Instructions – Download [optimized]
SentrySafe Lock Lawmaking Programming Instructions – Download